Kerr Centrifico Casting Machine: Difference between revisions
From Pumping Station One
m Robot: Cosmetic changes |
No edit summary |
||
| Line 13: | Line 13: | ||
}} | }} | ||
==Operation== | |||
*Start burnout process for flask | |||
*clamp machine to sturdy table | |||
*place chipboard box over machine (box currently (7/2015) located on top of lockers near back door) | |||
*wind machine counter clockwise for several turns | |||
*while holding wound machine, lift shiny metal bar upward and gently rest the swing arm against it | |||
**Pressure from swing arm will hold shiny bar in place | |||
*retract crucible tray (the metal bit that moves back and forth along the centrifugal arm axis) | |||
*start heating metal in separate crucible in a safe, nearby location. Preferably surrounded by firebrick | |||
*remove flask from burnout oven | |||
*place appropriately sized sheet metal support ring over heated investment flask | |||
**we have one for our wider flasks and one for the narrow flasks. Both are located with the flasks, crucibles, and casting machine | |||
*load flask and support ring onto the swinging arm | |||
*push crucible tray up against back of heated flask until snug | |||
*load crucible with molten metal into crucible tray. Keep under torch as much as possible to prevent oxidation. | |||
**Try not to torch the casting machine | |||
*pull counterweight slightly counterclockwise to release shiny metal bar | |||
*release counterweight and GET YOUR ARM OUT OF THE WAY | |||
*allow spinning arm to come to a complete stop before removing crucible/investment flask | |||
*dunk investment flask into water bucket to disintegrate investment | |||
*admire prize | |||
| Line 18: | Line 39: | ||
* better mounting for tables | * better mounting for tables | ||
* document the box you put around it to avoid splashy metal | * document the box you put around it to avoid splashy metal | ||
**Current box is kind of crappy, but works fine | |||
[[Category:Metalworking]] | [[Category:Metalworking]] | ||
[[Category:Hotmetals]] | [[Category:Hotmetals]] | ||
[[Category:Metal Casting]] | [[Category:Metal Casting]] | ||
Revision as of 20:57, 31 July 2015
 | |
| Owner/Loaner | PS:One |
|---|---|
| Serial Number | 42367 HD |
| Make/Model | Kerr Centrifico Casting Machine |
| Arrival Date | 2013 |
| Usability | yes |
| Contact | Eric Stein |
| Where | hot metals |
| Authorization Needed | no |
| Hackable | no |
| Estimated Value | ? |
| Host Area | {{{hostarea}}} |
Operation
- Start burnout process for flask
- clamp machine to sturdy table
- place chipboard box over machine (box currently (7/2015) located on top of lockers near back door)
- wind machine counter clockwise for several turns
- while holding wound machine, lift shiny metal bar upward and gently rest the swing arm against it
- Pressure from swing arm will hold shiny bar in place
- retract crucible tray (the metal bit that moves back and forth along the centrifugal arm axis)
- start heating metal in separate crucible in a safe, nearby location. Preferably surrounded by firebrick
- remove flask from burnout oven
- place appropriately sized sheet metal support ring over heated investment flask
- we have one for our wider flasks and one for the narrow flasks. Both are located with the flasks, crucibles, and casting machine
- load flask and support ring onto the swinging arm
- push crucible tray up against back of heated flask until snug
- load crucible with molten metal into crucible tray. Keep under torch as much as possible to prevent oxidation.
- Try not to torch the casting machine
- pull counterweight slightly counterclockwise to release shiny metal bar
- release counterweight and GET YOUR ARM OUT OF THE WAY
- allow spinning arm to come to a complete stop before removing crucible/investment flask
- dunk investment flask into water bucket to disintegrate investment
- admire prize
To-Do
- better mounting for tables
- document the box you put around it to avoid splashy metal
- Current box is kind of crappy, but works fine
