Evenheat 810 Kiln: Difference between revisions
From Pumping Station One
No edit summary |
m Robot: Cosmetic changes |
||
| Line 1: | Line 1: | ||
{{Template:EquipmentPage |owner=PS:One |model=Evenheat 810 |serial=38008 |arrived=2010 |doesitwork=Yes |contact=Eric Stein |where=? |certification=yes |hackable=no |value=$865}}<br> | {{Template:EquipmentPage |owner=PS:One |model=Evenheat 810 |serial=38008 |arrived=2010 |doesitwork=Yes |contact=Eric Stein |where=? |certification=yes |hackable=no |value=$865}}<br /> | ||
==History== | == History == | ||
On 1/28/2013 this was tested to at least power up and create heat. <br> | On 1/28/2013 this was tested to at least power up and create heat. <br /> | ||
3/3/2014. Inspect and test all mechanical and electrical components. <br> | 3/3/2014. Inspect and test all mechanical and electrical components. <br /> | ||
Remove upper switch, disassemble, clean contacts, reassemble and reinstall. <br> | Remove upper switch, disassemble, clean contacts, reassemble and reinstall. <br /> | ||
All components appear to works as intended. | All components appear to works as intended. | ||
==Heating Profile== | == Heating Profile == | ||
On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f. <br> | On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f. <br /> | ||
Room temp to 500f. | Room temp to 500f. 7 min. <br /> | ||
Room temp to 1000f. | Room temp to 1000f. 17 min. <br /> | ||
Room temp to 1500f. | Room temp to 1500f. 40 min. <br /> | ||
Room temp to 2000f. | Room temp to 2000f. 95 min. | ||
==Important Documents== | == Important Documents == | ||
*[http://www.evenheat-kiln.com/pdf/manual-c-810.pdf | * [http://www.evenheat-kiln.com/pdf/manual-c-810.pdf Manual] | ||
*[http://www.evenheat-kiln.com/pdf/manual-c-kiln-sitter-with-limit-timer.pdf Controller Manual] | * [http://www.evenheat-kiln.com/pdf/manual-c-kiln-sitter-with-limit-timer.pdf Controller Manual] | ||
*[http://www.evenheat-kiln.com/ceramic/technical/ Manufacturer's technical information] | * [http://www.evenheat-kiln.com/ceramic/technical/ Manufacturer's technical information] | ||
[[ | |||
[[Category:Photographs Needed]] | |||
[[Category:Shop Equipment]] | [[Category:Shop Equipment]] | ||
[[Category:Fabrication]] | [[Category:Fabrication]] | ||
[[Category:Craft]] | [[Category:Craft]] | ||
[[Category:Pottery]] | [[Category:Pottery]] | ||
Revision as of 18:11, 17 March 2014
| Owner/Loaner | PS:One |
|---|---|
| Serial Number | 38008 |
| Make/Model | Evenheat 810 |
| Arrival Date | 2010 |
| Usability | Yes |
| Contact | Eric Stein |
| Where | ? |
| Authorization Needed | yes |
| Hackable | no |
| Estimated Value | $865 |
| Host Area | {{{hostarea}}} |
History
On 1/28/2013 this was tested to at least power up and create heat.
3/3/2014. Inspect and test all mechanical and electrical components.
Remove upper switch, disassemble, clean contacts, reassemble and reinstall.
All components appear to works as intended.
Heating Profile
On 3/3/2014 I ran the kiln using a PID temperature controller set to 2200f.
Room temp to 500f. 7 min.
Room temp to 1000f. 17 min.
Room temp to 1500f. 40 min.
Room temp to 2000f. 95 min.
