Rockwell drill press: Difference between revisions
From Pumping Station One
Whosmollyk (talk | contribs) |
|||
| (35 intermediate revisions by 25 users not shown) | |||
| Line 1: | Line 1: | ||
{{Template:EquipmentPage | {{Template:EquipmentPage | ||
|image = | |image = rockwell-drill-press.jpg | ||
|owner=PS:One | |owner=PS:One | ||
|model=Rockwell 17-600 17" Drill Press | |model=Rockwell 17-600 17" Drill Press | ||
| Line 6: | Line 6: | ||
|serial=1456658 | |serial=1456658 | ||
|doesitwork=yes | |doesitwork=yes | ||
|where=Cold Metals | |where=Cold Metals | ||
|hostarea=Cold Metals | |||
|certification=yes | |certification=yes | ||
|hackable=no | |hackable=no | ||
| Line 29: | Line 29: | ||
Weight: 400 pounds | Weight: 400 pounds | ||
== Major Components == | |||
<gallery> | |||
File:rockwell-drill-press-control-boxes.jpg|The VFD (top) and spindle control box (bottom) | |||
File:rockwell-drill-press-main-power-switch.jpg|The main power switch, located on the back of the spindle control box, in the 'off' position; this needs to be 'on' for the VFD to receive power | |||
File:rockwell-drill-press-spindle-control-panel.jpg|The spindle control panel: the RPM readout (top; unpowered), RPM control knob (middle), and spindle power switch (bottom; off); the spindle power switch needs to be 'on' before the motor will turn the spindle | |||
File:rockwell-drill-press-emergency-stop.jpg|The emergency stop button, in the 'off' (pushed-in) position; needs to be rotated to the left to pop out into the 'on' position; the e-stop should be disengaged before the spindle power switch is toggled 'on' | |||
File:rockwell-drill-press-spindle-chuck.jpg|The spindle and the drill chuck which is more-or-less permanently inserted into it | |||
File:rockwell-drill-press-chuck-key.jpg|The chuck key and retaining magnet | |||
File:rockwell-drill-press-feed-lever.jpg|The feed lever, used to lower and raise the spindle | |||
File:rockwell-drill-press-depth-stop.jpg|The adjustable (by screwing it up or down) depth stop attached to the spindle, used to limit its downward travel | |||
File:rockwell-drill-press-table.jpg|The table, on which the work is placed or fixed | |||
File:rockwell-drill-press-table-height-handle.jpg|The handle used to adjust the height of the table; the table height lock needs to be disengaged before adjustment | |||
File:rockwell-drill-press-table-height-lock.jpg|The lever used to lock the height of the table, in the downward, 'locked' position | |||
</gallery> | |||
== Auth/Use Notes == | == Auth/Use Notes == | ||
Recommended Drill Protocol: | |||
#A full set of fractional, number and letter drills are available in a index case next to the drill. Use a drill from this case if one is available and usable. If a drill is unusable repair it or put it into the discarded drill tray. | |||
#If no drill is available or usable in the index case take one from the cabinets. | |||
#When you are through with the drill replace it into the index case. | |||
#With this procedure users can be assured that drills from the cabinet are new and drills from the index case may be OK but should be checked. | |||
These notes are for reference after authorization by a person. | These notes are for reference after authorization by a person. | ||
The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on. | The spindle switch must be 'off' and the e-stop (big red button) must be in the out position (twist the button counter clockwise) before the spindle can be turned on. Note-- If the VFD shows an E5 code check the e switch, it needs to be in the on (extended) position. | ||
Authorizations from the old DoAll drill press carry over to this machine. | Authorizations from the old DoAll drill press carry over to this machine. | ||
| Line 64: | Line 86: | ||
== List of Currently Authorized Users == | == List of Currently Authorized Users == | ||
{| class="wikitable" border="1" | {| class="wikitable" border="1" | ||
! Qualified Member | ! Qualified Member | ||
! Trained By | ! Trained By | ||
!Date | ! Date | ||
|- | |- | ||
|Dean Anderson | |Dean Anderson | ||
| Line 74: | Line 96: | ||
|Everett Wilson | |Everett Wilson | ||
|Dean Anderson | |Dean Anderson | ||
| | |||
|- | |- | ||
|Bruce Mace | |Bruce Mace | ||
| Line 90: | Line 113: | ||
|Chris Ruhland | |Chris Ruhland | ||
|4/09/2017 | |4/09/2017 | ||
|- | |||
|Carlos Garcia | |||
|Chris Ruhland | |||
|5/17/2017 | |||
|- | |||
|Ben Stringer | |||
|Chris Ruhland | |||
|5/17/2017 | |||
|- | |||
|Arjun Sharma | |||
|Tom Judge | |||
|8/10/17 | |||
|- | |||
|[[User:Ekaj|Jacob Snyder]] | |||
|Sam Olendorf | |||
|9/13/17 | |||
|- | |||
|Sean Nixon | |||
|Sam Olendorf | |||
|9/27/17 | |||
|- | |||
|Mateusz Pec | |||
|Sam Olendorf | |||
|9/27/17 | |||
|- | |||
|[[User:Bobbyh|Bobby Huggins]] | |||
|Sam Olendorf | |||
|11/15/17 | |||
|- | |||
|Ryan Himmelblau | |||
|Sam Olendorf | |||
|11/15/17 | |||
|- | |||
|Mac MacDevitt | |||
|Sam Olendorf | |||
|12/20/17 | |||
|- | |||
|[[User:wittnl|Nathan Witt]] | |||
|Sam Olendorf | |||
|11/29/17 | |||
|- | |||
|Aaron Vander Bee | |||
|Sam Olendorf | |||
|1/10/18 | |||
|- | |||
|Amanda Assaley | |||
|Sam Olendorf | |||
|1/10/18 | |||
|- | |||
|Stephanie Pelzer | |||
|Sam Olendorf | |||
|1/10/18 | |||
|- | |||
|Chris Eppig | |||
|Sam Olendorf | |||
|1/10/18 | |||
|- | |||
|Zack Sasnow | |||
|Sam Olendorf | |||
|1-26-2018 | |||
|- | |||
|Bill Schroeder | |||
|Sam Olendorf | |||
|4/18/2018 | |||
|- | |||
|Gary Newhouse | |||
|Eric Beauchamp | |||
|4/26/18 | |||
|- | |||
|Maciej Warchalowski | |||
|Sam Olendorf | |||
|6/13/18 | |||
|- | |||
|Alex Zhu | |||
|Sam Olendorf | |||
|7/25/18 | |||
|- | |||
|Malindima Sampa | |||
|McTavish McArdle | |||
|1/7/2020 | |||
|- | |||
|Michelle deLeon | |||
|McTavish McArdle | |||
|02/04/20} | |||
|- | |||
|Corwin Kline | |||
|McTavish McArdle | |||
|02/04/2020 | |||
|-} | |-} | ||
[[Category:Cold Metals]] | [[Category:Cold Metals]] | ||
