Boice Crane Drill Press: Difference between revisions
From Pumping Station One
No edit summary |
|||
| (20 intermediate revisions by 12 users not shown) | |||
| Line 1: | Line 1: | ||
{{Template:EquipmentPage | {{Template:EquipmentPage | ||
|image = boice_crane.jpg | |image = boice_crane.jpg | ||
|owner=PS:One | |owner=PS:One | ||
|model=Boice Crane | |model=Boice Crane 24103 24" Power Feed | ||
|arrived=January 2015 | |arrived=January 2015 | ||
|serial=23649 | |serial=23649 | ||
|doesitwork=yes | |doesitwork=yes | ||
|contact=Dean Anderson | |contact=Dean Anderson | ||
|where= | |where=Cold Metals | ||
|certification=yes | |certification=yes | ||
|hackable=no | |hackable=no | ||
|value=$600}} | |value=$600}} | ||
=Removal Section= | |||
*What is it? - Boice Crane Drill Press | |||
*Who is sponsoring? - Cold Metals Host - Jim Brink | |||
*Date published to the mailing list and RT- 06/11/2018 | |||
*Asset value - $100 | |||
*Suggested method of removal - Public sale- Craigslist | |||
*Background notes - | |||
*Resolution of removal - | |||
*Approval - | |||
== Specifications == | == Specifications == | ||
8 speed | |||
Gear-head. No belts or Jacobs chuck to slip, which means there is a lot of torque. | |||
Morse #3 taper spindle | |||
Capacity, cast iron 1 1/4" | |||
Drills to center 23" | |||
approximate weight 600 pounds | |||
motor HP 1.5 (high) 1.2 (low) | |||
Spindle speeds (8) 84, ... | |||
== Auth/Use Notes == | == Auth/Use Notes == | ||
| Line 23: | Line 50: | ||
Work piece needs secure mounting due to spindle's high torque | Work piece needs secure mounting due to spindle's high torque | ||
No through hole (table designed for coolant), must use vise | No through hole (table designed for coolant), must use vise | ||
No quill stop, must set table or head height to prevent drilling into table | No quill stop, must set table or head height to prevent drilling into table | ||
| Line 35: | Line 62: | ||
Drill shanks must be firmly seated in taper | Drill shanks must be firmly seated in taper | ||
To remove drill, | To remove drill, lower spindle to expose the slot in the quill, turn the spindle by hand until the quill slot lines up with the spindle slot, insert the #3 drift into the slot with the curved edge facing up, grasp drill, tap drift with hammer | ||
== To-Do == | == To-Do == | ||
| Line 52: | Line 79: | ||
== Maintenance == | == Maintenance == | ||
[[Boice_Crane_Drill_Press_maintenance|Boice_Crane_Drill_Press_maintenance]] | |||
== Equipment == | == Equipment == | ||
| Line 77: | Line 105: | ||
| Dean Anderson | | Dean Anderson | ||
|9/15/2015 | |9/15/2015 | ||
| | |||
|- | |||
|Greg Kudlacz | |||
|Todd Allen | |||
|- | |||
|Dafe Hughes | |||
|Todd Allen | |||
|- | |||
|Connor Sullivan | |||
|Tom Judge | |||
|1/22/16 | |||
|- | |||
|Abel Greenwald | |||
|Michael Patton | |||
|- | |||
|Bruce Mace | |||
|Chris Ruhland | |||
|3/7/17 | |||
|- | |||
|Sam Chen | |||
|Chris Ruhland | |||
|3/7/17 | |||
|- | |||
|Michael Ice | |||
|Sam Olendorf | |||
|2/08/18 | |||
|Aaron Hale | |||
|Sam Olendorf | |||
|8/8/2018 | |||
|-} | |-} | ||
[[Category: | [[Category:Cold Metals]] | ||
