LulzBot AO-100 3D Printer: Difference between revisions
From Pumping Station One
Rtystgeeke (talk | contribs) added ao100 config file |
|||
| (13 intermediate revisions by 9 users not shown) | |||
| Line 6: | Line 6: | ||
|serial = | |serial = | ||
|arrived = January 2013 | |arrived = January 2013 | ||
|doesitwork = | |doesitwork = no | ||
|contact = | |contact = [[CNC|CNC Area Host]] | ||
|where = [[CNC]] 2nd Floor | |where = [[CNC]] 2nd Floor | ||
|value = $1725 | |value = $1725 | ||
|itemphoto= | |itemphoto= | ||
| image = Lulzbot.jpg | | image = Lulzbot.jpg | ||
|hostarea = CNC | |||
}} | }} | ||
== Status == | == Status == | ||
As of 11/13/2015 Not working. RD | |||
I had to completely dismantle the extruder. Someone had jammed a ton of orange PLA in there. I even had to drill it out of the plastic part just above the hot end. There was melted material oozing out all kinds of places that it shouldn't be. | Working Beautifully! I had to completely dismantle the extruder. Someone had jammed a ton of orange PLA in there. I even had to drill it out of the plastic part just above the hot end. There was melted material oozing out all kinds of places that it shouldn't be. The actual hot end was packed full of this carbon type stuff (maybe over heated PLA?). I replaced the .5 extrusion tip with the .35 tip. I believe the .5 is permanently damaged due to abusive scraping of the tip. (Scraping the tip will not unclog the head) LG 5/14/2015 | ||
Hasn't been used much. Spool-holding bolt is inadequate to hold a spool. Doesn't appear to be extruding ABS even at 230 C. Investigating. RD 5/8/2015 | Hasn't been used much. Spool-holding bolt is inadequate to hold a spool. Doesn't appear to be extruding ABS even at 230 C. Investigating. RD 5/8/2015 | ||
| Line 39: | Line 40: | ||
=== Suggested Settings === | === Suggested Settings === | ||
Nozzle diameter = 0. | Nozzle diameter = 0.35 mm | ||
Filament diameter = 3.0 mm | Filament diameter = 3.0 mm | ||
COM port - | COM port - 4 (usually) | ||
Data rate = 115200 | Data rate = 115200 | ||
| Line 57: | Line 57: | ||
=== Other Resources === | === Other Resources === | ||
[http://download.lulzbot.com/AO-100/documentation/2012Q3/AO-100-User_Manual.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =) | [http://download.lulzbot.com/AO-100/documentation/2012Q3/AO-100-User_Manual.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =) | ||
[[Ao100config]] | |||
=== Filament === | === Filament === | ||
| Line 249: | Line 251: | ||
|Will Garza | |Will Garza | ||
|- | |- | ||
|[[user:kuroishi|Doorman Dave]] | |||
|Elizabeth Koprucki | |||
|- | |||
|[[user:stevenelson|Steve Nelson]] | |||
|Elizabeth Koprucki | |||
|- | |||
|Nem Simeunovic | |||
|Brad Jimenez | |||
|- | |||
|Dafe Hughes | |||
|Brad Jimenez | |||
|- | |||
|Gary Silver | |||
|Brad Jimenez | |||
|- | |||
|Daniel Maziarz | |||
|Brad Jimenez | |||
|- | |||
|Greg Kudlacz | |||
|Brad Jimenez | |||
|- | |||
|Adam Moffatt | |||
|Brad Jimenez | |||
|- | |||
[[Category:Fabrication]] | [[Category:Fabrication]] | ||
