LulzBot AO-100 3D Printer: Difference between revisions
From Pumping Station One
Rtystgeeke (talk | contribs) added ao100 config file |
|||
| (30 intermediate revisions by 20 users not shown) | |||
| Line 6: | Line 6: | ||
|serial = | |serial = | ||
|arrived = January 2013 | |arrived = January 2013 | ||
|doesitwork = | |doesitwork = no | ||
|contact = | |contact = [[CNC|CNC Area Host]] | ||
|where = [[CNC]] 2nd Floor | |where = [[CNC]] 2nd Floor | ||
|value = $1725 | |value = $1725 | ||
|itemphoto= | |itemphoto= | ||
| image = Lulzbot.jpg | | image = Lulzbot.jpg | ||
|hostarea = CNC | |||
}} | }} | ||
== Status == | |||
As of 11/13/2015 Not working. RD | |||
Working Beautifully! I had to completely dismantle the extruder. Someone had jammed a ton of orange PLA in there. I even had to drill it out of the plastic part just above the hot end. There was melted material oozing out all kinds of places that it shouldn't be. The actual hot end was packed full of this carbon type stuff (maybe over heated PLA?). I replaced the .5 extrusion tip with the .35 tip. I believe the .5 is permanently damaged due to abusive scraping of the tip. (Scraping the tip will not unclog the head) LG 5/14/2015 | |||
Hasn't been used much. Spool-holding bolt is inadequate to hold a spool. Doesn't appear to be extruding ABS even at 230 C. Investigating. RD 5/8/2015 | |||
== Operation == | == Operation == | ||
Don't forget to turn the printer off when you are no longer using it. Also, wipe your own nose. | |||
=== Windows Drivers === | === Windows Drivers === | ||
| Line 30: | Line 37: | ||
* [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs | * [https://github.com/kliment/Printrun#getting-printrun Pronterface] - or [http://www.repetier.com/download/ Repeteir-Host] for manual operation of the printer as well as for starting print jobs | ||
* [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models | * [http://slic3r.org/download Slic3r] - for creating gcode (print jobs) from 3D models | ||
* Additionally, Lulzbot provides a [http:// | * Additionally, Lulzbot provides a [http://download.lulzbot.com/AO-100/software/2012-Q2/configs/slic3r/point5mm.ini config file] for the AO-100 LulzBot. (Note: remember to change nozzle to .5 after importing the config file.) | ||
=== Suggested Settings === | === Suggested Settings === | ||
Nozzle diameter = 0. | Nozzle diameter = 0.35 mm | ||
Filament diameter = 3.0 mm | Filament diameter = 3.0 mm | ||
COM port - | COM port - 4 (usually) | ||
Data rate = 115200 | Data rate = 115200 | ||
| Line 50: | Line 57: | ||
=== Other Resources === | === Other Resources === | ||
[http://download.lulzbot.com/AO-100/documentation/2012Q3/AO-100-User_Manual.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =) | [http://download.lulzbot.com/AO-100/documentation/2012Q3/AO-100-User_Manual.pdf The manual is available online]. A printed form of it can be found near the printer. The manual explains how to operate the printer. Read it =) | ||
[[Ao100config]] | |||
=== Filament === | === Filament === | ||
| Line 208: | Line 217: | ||
|Scott Little | |Scott Little | ||
|Derek Bever | |Derek Bever | ||
|- | |||
|Alex Maties | |||
|Elizabeth Koprucki | |||
|- | |- | ||
|Bruce Sanders | |Bruce Sanders | ||
| Line 215: | Line 227: | ||
|Justin Conroy & Ray Doeksen | |Justin Conroy & Ray Doeksen | ||
|- | |- | ||
| | |Mike Mandrea | ||
|Elizabeth Koprucki | |||
|- | |||
|Andy Richardson | |||
|Elizabeth Koprucki | |||
|- | |||
|Eric Yu | |||
|Elizabeth Koprucki | |||
|- | |||
|[[User:rickalm|Rick Alm]] | |||
|Elizabeth Koprucki | |||
|- | |||
|Davis Mazariegos | |||
|Elizabeth Koprucki | |||
|- | |||
|Knute Martell | |||
|Elizabeth Koprucki | |||
|- | |||
|[[User:Tina|Tina C]] | |||
|Elizabeth Koprucki | |||
|- | |||
|Ryan Neuman | |||
|Will Garza | |||
|- | |||
|[[user:kuroishi|Doorman Dave]] | |||
|Elizabeth Koprucki | |||
|- | |||
|[[user:stevenelson|Steve Nelson]] | |||
|Elizabeth Koprucki | |||
|- | |||
|Nem Simeunovic | |||
|Brad Jimenez | |||
|- | |||
|Dafe Hughes | |||
|Brad Jimenez | |||
|- | |||
|Gary Silver | |||
|Brad Jimenez | |||
|- | |||
|Daniel Maziarz | |||
|Brad Jimenez | |||
|- | |||
|Greg Kudlacz | |||
|Brad Jimenez | |||
|- | |||
|Adam Moffatt | |||
|Brad Jimenez | |||
|- | |||
[[Category:Fabrication]] | [[Category:Fabrication]] | ||
